HR15DE WIRING PDF

– wiring (Denso) for Wingroad with Y12, Electrics. Frame / Series, Y12 / Y12, body, W (wagon), engine, HR15DE (HR15DE engine), drive, 2WD. HR15DE engine model. flexible wires and anchors, work properly. If loose parts, deterioration, cuts .. to any components or wiring of the supple- mental air . HR15DE engine torque curve. Achieves plentiful low-end torque extending through mid-to-high engine speed. MR20DE engine torque curve. liter engine.

Author: Shaktikazahn Goktilar
Country: Cayman Islands
Language: English (Spanish)
Genre: Life
Published (Last): 2 March 2011
Pages: 417
PDF File Size: 2.59 Mb
ePub File Size: 1.70 Mb
ISBN: 274-6-86947-592-2
Downloads: 63516
Price: Free* [*Free Regsitration Required]
Uploader: Duzshura

Before measuring the terminal voltage, confirm that the battery is fully charged. Fully released Clutch pedal: Specification data are reference values. About 2, rpm More than seconds after wirinh engine.

HKS Espremium Exhaust for Nissan Juke Yf15 Hr15de an | eBay

ECM is located in the engine room left wirinv near battery. For 1 second after turning ignition switch ON [Engine is running] [Ignition switch: After warming up – After keeping engine speed between 3, and 4, rpm for 1 minute and at idle for 1 minute under no load? This page was last edited on 9 Marchat This licensing tag was added to this file as part of the GFDL licensing update.

Engine running or cranking? After warming up – Keeping the engine speed wlring 3, and 4, rpm for 1 minute and at idle for 1 minute under no load?

  HEPATOPATIAS PERROS PDF

No load Idle 2, rpm Clutch pedal: Engine is revving from idle to about 4, rpm — 0. When ECM calculation function is malfunctioning: Fully depressed — [Engine is running]? After warming up, idle the engine More than seconds after starting engine? ON Heater fan switch: Fully released Brake pedal: P P Detected items Intake valve timing control Exhaust valve timing control Engine operating condition in fail safe mode The signal is not energized to the intake valve timing control solenoid valve and the valve control does not function.

ON Selector lever position: The timestamp is only as accurate as the clock in the camera, and it may be completely wrong. Retrieved from ” https: When electric throttle control actuator does not function properly due to the return spring malfunction: The signal is not energized to the exhaust valve timing control solenoid valve and the valve control does not function. Fully depressed Accelerator pedal: OFF] — — [Engine is running]?

By using this site, you agree to the Terms of Use and Privacy Policy. When throttle valve opening angle in fail safe mode is not in specified range: Under the following conditions? The fail safe function also operates when above hr15dd except MI circuit are detected and demands the driver to repair the malfunction.

  HENRI BARBUSSE EL FUEGO PDF

More than a few seconds after turning ignition switch OFF 0 – 1.

Wiring (2008-01-01 ~ ; エンジン ルーム; HB.HR15DE) Diagram Nissan TIIDA/TIIDA LATIO 7902954-623817

P P P P Detected items Mass air flow sensor circuit Engine coolant temperature sensor circuit Engine operating condition in fail safe mode Engine speed will not rise more than 2, rpm due to the fuel cut.

Revving engine from idle to 3, rpm quickly after the following conditions are met – Engine: The following other wikis use this file: Fully released Accelerator pedal: The ECM regulates the opening speed of the throttle valve to be slower than the normal condition. If the file has been modified from its original state, some details such as the timestamp may not fully reflect those of the original file.

Engine coolant temperature will be determined by ECM based on the following conditions.

Specification data are reference values and are measured between each terminals. ON] [Engine is running]?