CARDAX 6000 PDF

Cardax FT Controller – Download as PDF File .pdf), Text File .txt) or read online. Installation Guide. Cardax FT Controller CAUTION This equipment contains components that can be damaged by electrostatic discharge. Ensure both you. The Gallagher Controller supports the following door readers: > Cardax IV Prox (Mifare, kHz, TIRIS). > Cardax IV Prox Plus (Mifare, kHz,. TIRIS).

Author: Zulkikasa Negar
Country: Jamaica
Language: English (Spanish)
Genre: Science
Published (Last): 6 August 2007
Pages: 202
PDF File Size: 17.11 Mb
ePub File Size: 12.34 Mb
ISBN: 417-6-70948-705-9
Downloads: 31179
Price: Free* [*Free Regsitration Required]
Uploader: Kasida

Switch on power to the Cardax FT Controller Initialise the Cardax FT Controller The power supply cable must be of sufficient size to ensure that the voltage at the GBUS unit terminals is the recommended 12 Vdc.

The Gallagher Controller R has on-board connections for with variations for the Gallagher Controller R shown in brackets: There is a proprietary czrdax communication protocol between the two boards.

Boot code monitor running.

Gallagher Controllers | AES Group Ltd.

The Enter Network Password screen displays. Ensure that the power to the Cardax FT Controller is switched off and disconnected. On startup, the main application is run. Normal Startup – Configuration will be retained. This port is provided for external communications to be connected to the system.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. Cardax FT Version 5.

The software is powerful, In the event of a catastrophic failure, after approximately 60 seconds the In-Service relay opens. Click the OK button. The following initialisation procedures are detailed in the later cardaax titled “Initialisation”: On startup configuration and the IP address is deleted.

Both variants of the Controller can operate on their own, or can have an optional Reader Module part number C or C connected. These contacts close when the Controller is powered up, and remain closed until either the power 600 removed csrdax there is a ‘Catastrophic Failure’.

  FOCLOIR POCA PDF

This means in the event of network communications being disrupted, security cardzx maintained on site. Follow the steps below to access the Controller’s Config web page: Install the component identification decal inside the Cardax FT Cabinet door.

Standard and High Specis a processing board for an intruder alarm and access control system. Refer to the previous section “Component layout” for the location of the plugs.

Note that this cable type is only suitable for the communications circuits. Looking at the Controller it will be obvious that the there is no ethernet activity on either ethernet connection, as the RJ45 connector LEDs will not be operating, and the Controllers run LED will be 66000 2 flash. Because this Controller does not incorporate on-board reader connections it provides a cost-effective solution where ‘alarms-only’ is required. The termination jumper on either GBUS circuit needs to be fitted if the Controller is the end device for this circuit.

The Gallagher Controller is specifically designed to support access controlled doors and integrated intruder alarms.

Flash Slow Fast 1 flash 2 flashes Sequence timing Meaningms on, ms off Controller is searching for software FTS files ms on, ms off 4Hz flash ms on, ms off 1Hz flash 2 flashes – pause each flash is 50ms on, 600 off, 1.

Communication between Cardax FT Controllers and lower level hardware items uses two Cardax-proprietary data communication formats. Cardwx to Component layout within this Installation Note for the location of the serial socket. The cables should stow neatly and be held in place by the cable clamps fitted into the base of the Cabinet. Dardax on the power supply. Overview The Gallagher Controllers are intelligent field controllers, programmed to make access control and intruder alarm decisions in the field, independent of the Cardqx Command Center.

  BRENDAN BRAZIER THRIVE DIET PDF

It is an Ethernet attached device which connects to a server, however it can operate autonomously. The cabling between GBUS devices should be done in a daisy chain or serial format, i. This indicates the Cardax FT Controller is waiting for database information to be downloaded from the Server.

When using these connection points, ensure the Power Supply to the Cardax FT Controller is capable of supplying the extra current required. Card readers Intruder Alarms may be installed in elevator cars to Documents. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

An upgrade of the Controller software via a USB memory stick is complete and the USB drive must be removed for installation to complete. Switch off the power supply to the Cardax FT Controller. On-board connections are provided for: Set switch 2 to ON closed. Unused Unused Boot normally. Page 2 1 Cadrax Introduction Providing flexible configuration options to meet specific site requirements, Gallagher Controllers: Cardax Ft Controller pdf Download Report.

Cardax Ft Controller 6000pdf

Cardax FT Controller Documents. Install all the system 600 power cables. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause 600 interference to radio communications. This takes approximately 11 seconds, while data is being written to memory. When the Controller has a Reader Module connected, it receives information from the Reader Module about access requests and instructs the Reader Module to carry out the required function.