24C02 I2C PDF

The programming and reading of I2C EEProms is one of the major uses of the as 2,4 or 8 separate 24C02 memories with sequential I2C sub-. I am trying to read and write I2C EEPROM (24C02 from Microchip) but i failed every-time. i am using Kohms as a pull up resistor in the I2C bus. My code is. Now the problem is: as I go through the datasheets of all such I2C serial memories there is a memory reset in that of AT24C02 which is not.

Author: Vura Kit
Country: Greece
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 26 May 2014
Pages: 257
PDF File Size: 7.11 Mb
ePub File Size: 7.57 Mb
ISBN: 275-4-56151-676-8
Downloads: 44347
Price: Free* [*Free Regsitration Required]
Uploader: Nilrajas

I can’t see anything obviously wrong. Donec dictum ipsum 24c2, in commodo eros facilisis at. These 3 bits must compare to their corresponding hard-wired input pins. In reply to sagar: The A0, A1 and A2 pins are no connects and can be connected to ground.

eeprom 24c02 interface using I2C with F28069

Please Help, I am new to I2C device. Acknowledge has negative polarity, while negative acknowledge has positive polarity. Welcome to our site!

At reset, if I release the data line and it is still low then I send clock pulses until the data line is high. The interesting thing that you should try is to put delay.

So I think, you might be talking about something that has to do with this. Hello Sagar, Seems that still nobody can help you in your case random read and write-read multiple bytes.


The two device address bits must compare to their corresponding hard-wired input pins. This thread has been locked. These page addressing bits on the 4K, 8K and 16K devices should be considered the most significant bits of the i2f word address which follows.

Nov 29, 3: Electro Tech is an online community with overmembers who enjoy talking about and building electronic circuits, projects and gadgets. Don’t forget to acknowledge during read operations, acknowledge only if you are going to read another byte, and negative acknowledge after the last read, right before stop.

Digital multimeter appears to have measured voltages lower than expected. What i called Data Addresscould be byte or more. In reply to Maria Todorova: Forums New posts Search forums. Distorted Sine output from Transformer i2d. Found 2 device s. Thanks for the advice.

Problem with reading I2C EEPROM (24C02) – Question | Mbed

The time now is I2C bus 24C08 and 24C64 Problem 3. Dec 3, 4: Based on this website: Yes it looks much better. We are glad that we were able to resolve this issue, and will now proceed to close this thread.

The A0 pin is no connect. Many thanks for 24c002 help.

24C02 – 2 Kbit Serial I2C Bus EEPROM

If so please help me with its routine. Here is the code and now it works great!

Dec 242: Found 1 device s. I hope I’m clear enough as I’m a beginner and English is not my first language. I got the expected data. The A0 pin is a no connect and can be connected to ground.


Officially you need to transmit a restart after setting the read address, although I dont think it should matter this time. Trademarks Privacy Policy Terms of Use.

Equating complex number interms of the other 6. Please find attached waveform which I captured foe 2 byte write operation. How to set I2C address 24C02 24C Unfortunately, no change El Supreremo!

Turn on power triac – proposed circuit analysis 0. Normally, both devices get reset on power down and so the problem doesn’t arise. PaulS Brattain Member Posts: Hello Nick It gives: Access Warning You do not have the correct permissions to perform this operation. Hello Maria, Thanks for continue support.

And I’m not a programmer, so till now I’ve been mostly copying different pieces of code and modifying some part, then look what was happening. It only uses one byte of addressing so you would have to address it like this: Intellectual points sagar Nov 26, 6: All postings and use 24c2 the content on this site are subject to the Terms of Use of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Terms of Use of this site.

For a better experience, please enable JavaScript in your browser before proceeding.